-59%
0%

FERRARI & MASERATI SD3 Diagnostics Scanner Tools Cover SD2/SD3 For All FERRARI & MASERATI Models- 458 and California

$19,000.00 $7,800.00

Brand Name : SD3 AutoTools
Model Number : SD3 Auto Diagnostic Tools
Certification : CE
Place of Origin : China (Mainland)
MOQ : 1 Pieces
Supply Ability : 5000 Unit/Set
Delivery Time : 2 to 5 Working Days
Packaging Details : Single flight case ,double flight case ,exported carton. It’s all up to customer’s requirements.
Payment Terms : T/T , Western Union , MoneyGram
Color : silver
Type : Engine Analyzer
Operating system:- : Runs on Windows CE, a robust, real-time
Microprocessor:- : 80 MHz Hitachi® SH3
Applicable Models : For FERRARI & MASERATI Tester Tool
Memory Internal Flash :- : 32MB
Display :- : 1/4 VGA (240 by 320 pixels) color, 3.5 in. (8.9 cm) transflective display with touch screen, Anti-glare coated
System Card :- : 32 1 GB secure digital card
Warranty : Accepted 12 Months with Six Month Replacement
Replacement : 6 Months
Available:- : In Stock Ready For Shipment
RAM : In 32 MBstock
Full Refund::- : Accepted
Voltage:- : 12 V
Power : 9 W
Weight :- : Approximately 1.65 lb. (0.75kg) with battery
Description

Description

The FERRARI & MASERATI  SD3 Diagnostic System Is Supplied With A Suitcase Containing

Specifications

Original for FERRARI & for MASERATI Tester including the 458 and California models

For FERRARI for MASERATI SD3 Tester

Of The the SD3 Diagnostics the System IS AN Electronic Device for The Diagnostics of Electronic Control Units (the ECU) Installed in AND ECONOMICS Vehicles.
Of The the SD3 Diagnostics System IS A with palmtop Device with A backlit Color the LCD the display and A membrane Keypad with Twenty Keys;

It IS Also Equipped with :
-three Standard RS232C Serial Lines;
-SiX Standard ISO9141 / CARB / 2000 KEYWORD Serial Lines;
-two Standard CAN Serial Lines Multimeter in Volts Operating Temperature Range (up to 200 V DC) and Ohm (up to 1 Mohm)

 

 

Supported Model

  • Cover SD2 / SD3 Until 2016
  • 3200 GT (3200 GT)
  • Ghibli (M157)
  • Gransport (Gransport)
  • GranTurismo (M145)
  • GT (M138)
  • Quattroporte (M139)
  • Quattroporte (M156)
  • Quattroporte MY (M139 MY)

Software

  • MDVCI-Diagnosis software
  • Spare part catalogue
  • Wiring diagram
  • Service menu / Work hour menu
  • Module location menu
  • Diagnosis/Guide Function
  • Live data / Coding
  • Active/Special function
  • Programming ( Immobilizer system need ON-Line Access account )

 

 

It can be interfaced to a PC containing the software required to update the ECU diagnostics software through one of the following lines:

>> standard RS232C serial line
>> USB serial line
>> Ethernet 10/100Mbit network
>> Ethernet Wireless 802.11b network

For better efficiency and faster data transfer between the PC and the SD3 unit, we suggest you use the USB line or an Ethernet/Wireless network for communications.

The System IS Supplied the SD3 the Diagnostic of The A with Suitcase containing:
>> the SD3 Tester;
>> Serial Cable for the SD3 / SD2 are Connection to the PC (the SD3-CBL01) [095 970 327];
>> Multimeter Cable (the SD3-CBL02) [095 970 328];
> > Power supply feeder (SD3-CBL05) [095970331];
>> EOBD SD3 diagnosis cable (SD3-CBL06) [095970332];
>> Diagnosis cable with SD2 bridle ( SD3-CBL07) [095970333];
>> Connection cable for feeding Among SD2 and SD3 bridle (SD3-CBL08) [095970334];
>> Cigar lighter socket feeder (SD3-CBL09) [095970335];
>> ISO 1 extension (SD3 -CBL10) [095970336];
>> ISO 2 extension (SD3 -CBL11) [095970337];
>>SD2 B-CAN adapter (SD3-CBL12);
>> USB cable [095970330];
>> 10/100 Mbps Ethernet cross-over cable [095970329];
>> SD3 wireless board; SD3 Manual [095970324];
>> SD3 Quick Reference;
>> Installation CD-ROM [095970326];
>> 8 metal-point rods For Multimeter.
>> PC USB/Wireless board

 

To install the Basic SD3NET software on the PC, proceed as follows:

1. Power the the PC where the program has to be installed;
2. Insert the program CD supplied with the SD3 in the CD drive.
3. If the user has enabled The AUTORUN function on the CD drive, the installation wizard will launch automatically ; in this case go to point 7, otherwise continue the procedure below;
4. Using your mouse, double-click on MY COMPUTER;
5. When the computer resources window opens Double-click on the CD icon where the SD3NET program has been inserted ;
6. The Double-Clicking Opens window A Showing The Contents of the CD The Double ON the Click the SETUP.EXE Installation of The Wizard Will now RUN;..
7. The displayed for BE A window Will The Selection of The Language The During Program Installing to use.
8. The installation wizard displays a start window. Click on NEXT to continue;
9. You will be prompted to install Microsoft Framework NET 1.1 (if It is not present). Always confirm and proceed with installation;
10. You are asked to name The directory in which the program will be installed (we recommend leaving the default setting). Click on NEXT to continue;
11. You are asked to The Directory in Which the DATA name The Program Will BE Installed (WE Recommend Leaving Setting The default) Continue to the Click the NEXT ON;.
.
12. The window of The Last Gives A Summary of The Previous Selections The Press and the NEXT COPYING The Program System Soho starts to your PC.
13. When the installation has terminated you will be asked to reboot your PC. This is essential for the program to operate correctly;
14. When the PC has been rebooted, the SD3NET? icon will appear on the desktop.

 

 

Multimeter

The SD3 Diagnostics System has an integrated multimeter that can take measurements in Volts (up to 200 V dc) and Ohms (up to 1 Mohm). This function can be selected from the SD3 Tester main menu.

ScantoolOBD

The SD3 Diagnostics System has an integrated Standard Scantool OBD software. This system makes it possible to automatically check for systems able to support the service (engine, shift, …). Once the control unit has been identified by the software, you can Check some parameters/errors supplied by the system itself.

This function can be selected from the SD3 Tester main menu.

 

Power supply voltage

The SD3 requires a voltage between 8 and 16 V DC which is supplied either by the battery of the vehicle being tested or by the power supply provided with the product.

 

Installation instructions for the SD3

The SD3 does not require any installation; it only needs to be configured with the diagnostics software to be used. The downloaded software are stored in the non-volatile memory of the SD3 unit. The SD3 is equipped with a battery-powered clock which can Be set and checked on the PC through a special software menu.

 

General Description

The figures are provided a diagram of the upper part (containing the power supply and diagnostics connectors), front part of the SD3 unit (containing the display, keypad and ON light) and the lower part (containing a flap which provides access to the lower part Part Part Used to hook up an American PS2 keyboard for the PC, and two PCMCIA connectors used for any hardware expansions-eg flash expansions, Wireless card-through external boxes).

 

The ten keys at the bottom of the screen are used to input data (numbers/letters) into the diagnostics software.

The directional arrows and the TAB key feature function repetition if the key is held down continuously.

In all menus, hold down “Switch” and “Esc” for 4 seconds to reset the SD3 Tester software. This speeds up restarting the device if the software crashes (the Tester does not respond to the keywords commands).

The top holds the following :

· The power button.

· One 25-pin connector for power and serial diagnostics lines (on the power button side);

· One 9-pin connector (male) for hook up to the PC (in the centre);

· One 9-pin connector (female) for Multimeter inlet.

· One Ethernet 10/100 Mbit connector.

· One USB connector.

· One Connector to hook up a CRT VGA monitor

 

Self test

To quickly check that the device is functional, connect the power supply (for example, with the cord

And the mains power supply), press the power button and check that the led lights up. Within 20/30 seconds

The start icon appears on the display.

The SD3 has a resettable fuse. If it is activated because of an internal fault or due to the external cabling,

Wait a few minutes to allow it to reset. If, when you switch on the SD3, the display does not light up, wait a

Few minutes and repeat the procedure.

 

Product Highlights

  • New silver edition celebrates 25 years of handheld status
  • Full-color graphical user interface
  • Powerful field diagnostics
  • Bluetooth® communication
  • Long-lasting Lithium-Ion power module
  • Universal support for HART and FOUNDATION fieldbus devices
  • The 475 Field Communicator builds on the industry-leading technology of the 375 Field Communicator while adding innovative new capabilities including color display, Bluetooth communication, and advanced field diagnostics
  • What you get is the most powerful handheld available – universal, user upgradeable, intrinsically safe, rugged and reliable
  • Runs on Windows CE, a robust, real-time operating system
  • Microprocessor – 80 MHz Hitachi® SH3
  • Memory Internal Flash – 32 MB
  • System Card – 1 GB secure digital card
  • RAM – 32 MB
  • Display – 1/4 VGA (240 by 320 pixels) color, 3.5 in. (8.9 cm) transflective display with touch screen, Anti-glare coated
  • Weight – Approximately 1.65 lb. (0.75kg) with battery
Emerson Process Management Rosemount Field Communicator 475 Features
Microprocessor 80 MHz Hitachi SH3
Memory Internal Flash 32MB
System Card 1GB Secure Digital Card
RMB 32MB
Weight Approx. 1.65 1b (0.75kg) with Battery
Display 1/4 VGA (240 * 320 px) color, 3.5 in (8,9 cm) transreflective display with touchscreen, anti-glare coated
Keypad 25 keys including 4 action keys, 12 alphanumeric keys, tab key, function key, backlight key, power key,and 4 cursor-control (arrow) keys;membrane design with tactile feedback
Battery Rechargeable lithium-lon power module
Battery Charger Min DIN 6-pin Jack
Environment 
Usage
10° C (14° F ) to +50° C (122° F )
HART 
Fieldbus
Three 4mm banana plugs (one common to HART and Foundation fieldbus)
Blue tooth Up to 32.8 ft (10 m) communication distance
Uses standard Windows drivers 
FCC, IC and CE approvals
Easy Upgrade
Requirements
Usage
PC with Internet access
CD Rom drive
IrDA port (or adapter) or Bluetooth (or adapter)
SD Card Reader (required for some upgrades)
Windows XP (SP2 or SP3) or Windows Vista Business (SP1)

Each Unit Includes

  • Field Communicator
  • System Card
  • Power Module and Recharger
  • Lead Set with Connectors
  • Carrying Case
  • User’s Manual and Getting Started Guide
  • 475 Resource CD
  • Straps

 

Product Detail Image
  • Photo 3.JPG

 

OFF-LINE CODING IS ALSO POSSIBLE (online is, per time fee)

All cables are the latest versions with full support.

We are an established company.

Free technical support available by appointment.

.

All software will be pre-installed for you.
The system is built to order and delivered READY TO USE. 

All cables supplied will be brand new.

TXS Global Store Ltd.

We supply all manner of diagnostics setups

for cars and trucks.

Contact us if you have more or any queries.

DISCOUNTS FOR /BANK TRANSFER/WIRE PAYMENTS /MONEY GRAM AVAILABLE or MULTI BUY. Contact us.

Delivery:

We will deliver your products as soon as possible after confirming with your payment.
All items had been tested before shipping

please give correct post code to avoid delay of shipment

Russia customer needs to provide full name, normally it have three name

please provide English delivery address

Tax:

We can declare in lower value to help you avoid tax, if you have any idea about this , please tell after paid

buyer is responsible to clear customs and pay tax if any when goods arrive their country,  our price does not include tax in your country,

thanks

Returns:

We do our best to serve our each customer the best that we can.
We will refund you for items returned within 7 days of you receiving them, for any reason.

A full Refund will be given if items are returned in their original condition.
Merchandise which is damaged or missing components is not refundable.
Buyers are responsible for return shipping with proper packaging.
On receiving items, we will refund you immediately.

Warranty & Maintenance:
We provide 1 year warranty, Buyers are only responsible for the return shipping fees for warranty items. As soon as we receive the items,

we will repair or exchange them ASAP.

Feedback:
Your positive feedback will be highly appreciated once you get the items and satisfied with them. Also we will be very glad to return you the
positive feedback. Thank you!

Contact us:

Please Make Sure You Leave A  Message At The End of  Email below for Fast Response or Reply.
And if nobody answers you online, sometimes, do not worry, leave us a message or write your desires, we will contact you as soon as possible. , We Will GET Back to you immediately.
Thanks for your Understanding.

Contact us:

Our office hours:

Am8: 30-PM11: 00

Contact Information.
Live Support: Chat with us online

Email: txsglobalstore@zoho.com
Sales@txsglobalstore.com

For Direct Live Chat: Visit Us @

Www.txsglobalstore.com

Technical & Specification Details
Emerson Process Management Rosemount Field Communicator 475 Features Microprocessor 80 MHz Hitachi SH3 Memory Internal Flash 32MB System Card 1GB Secure Digital Card RMB 32MB Weight Approx. 1.65 1b (0.75kg) with Battery Display 1/4 VGA (240 * 320 px) color, 3.5 in (8,9 cm) transreflective display with touchscreen, anti-glare coated Keypad 25 keys including 4 action keys, 12 alphanumeric keys, tab key, function key, backlight key, power key,and 4 cursor-control (arrow) keys;membrane design with tactile feedback Battery Rechargeable lithium-lon power module Battery Charger Min DIN 6-pin Jack Environment Usage 10° C (14° F ) to +50° C (122° F ) HART Fieldbus Three 4mm banana plugs (one common to HART and Foundation fieldbus) Blue tooth Up to 32.8 ft (10 m) communication distance Uses standard Windows drivers FCC, IC and CE approvals Easy Upgrade Requirements Usage PC with Internet access CD Rom drive IrDA port (or adapter) or Bluetooth (or adapter) SD Card Reader (required for some upgrades) Windows XP (SP2 or SP3) or Windows Vista Business (SP1)